Just installed the 24 port POE version (JL683A ). The fan seems to run at full speed without variation. Much louder then the Netgear Smart POE switch it replaced. However, the Data Sheet says...“Energy-efficient coolingIncludes variable speed fans operating only at the speed necessary to maintain operating temperature to reduce excess noise and power consumption.”
https://www.arubainstanton.com/files/DS_AIO_1930SwitchSeries.pdfWill this be addressed in a future update?
@FukuokaKid Thank you for the feedback and we will make sure this is passed to product management for review.
I also received and installed this Aruba Instant On 1930 48G 370W (JL686A) switch a week ago.
Unfortunately I should have read these comments before...
I am also concerned about the fan making too much noise. It is very annoying.
I don't think I will keep it if no official software/hardware solution is brought in quickly.
I'm disappointed because this switch suited me perfectly.
Can we have a quick feedback please?
JL683A updated to FW to the latest,126.96.36.199_125. No change to the fan speeds. What's more there are no release notes posted for this version.
Guess it's going back in storage for now.
@FukuokaKid Here is a link to the release notes.
Mine was also loud and not slowing down, exact same model, latest firmware.
Mine does the exact same thing on. It's annoying because it's incredibly loud.
I ordered this switch for me and myself and for me the fan was also too loud.
I disassembled the switch and the part number on this fan shows that it is build for 4000 - 10000 rpm. So it's loudness reaches from very very loud to very super mega loud!
The Fan IS speed controlled!
next to the fan connector there is an PTC or NTC (blue, very small part) when you touch it (and warm it up with thefinger) the fan speed increases.
Because the fan does not change the rpm during boot (as it do on old, solid HPE Switches) I am sure the control circuit is a dedicated and analog circuit and the os of this switch can not control the fan speed rpm.
The connector's pinout is compatible with any mainboard / intel fan (4 pin PWM).
For test purposes I Connected an genuine intel CPU fan and it also runs normally.
So, I decided to build my own upper case with a 12cm x 12cm hole on the top right with an arctic cooling 12x12 4 pin PWM fan. It is blowing there inside the switch and the air flow is coming out on the left side through 2 holes.
This fan runs at approx 1000rpm and generates much more airflow than the small 4x4cm fan at much more rpm does.
only thing is, the air flow goes into the other direction. Normally the airflow is from left to right, the fan blows the air out of the switch and the NTC / PTC next to the fan can see how much heat is produced by the switch and can control the fan speed.
now the NTC / PTC is only measuring the intake air and can not react on the switch load.
Also the problem at the moment is, the Tacho signal is so low due the low fan speed, that the switch interprets the fan as defective and displays an error (red blinking light and fan error in the logs)...
When I pull out the PIN 4 (PWM control for the fan) the fan accelerates to its maximum speed (1800rpm) and the switch goes back to normal state. But at this moment the 1800rpm are totally overdosed with this 12cm fan and you can hear it and see in its power consumption.
Now I am planning to rebuild my own case, set the fan to the left top, so the airflow is as normal and the PTC / NTC measures the outtake temperature and I am planning to build (or buy) an small frequency generator (NE555) to simulate a solid and higher fan speed to the Switch to let the switch be in normal state.
Hope this helps anyone
Yeah so this 24 port 195W 1930 switch is ridiculously LOUD!!! This is flat out the loudest switch I have ever heard. Not to mention it's odd that the 370w is rated as being quieter?!? I have this in my garage, and I can hear it clear as day in the laundry room with the door closed. I don't know how I could even sell this to a client who doesn't have an extremely isolated system room, and this is marketed to SMBs, who often don't have such luxuries.
I don't know Aruba, I don't see how I can sell your PoE switches. I can get past it for me in the garage, but Jesus, it starts LOUD and stays LOUD. Poor cooling design decisions here. And I really don't want to mod it for fear of losing warranty. I certainly wouldn't mod it for clients. How did anyone think this was a good idea to put out something that sounds like a vacuum cleaner? I won't sell them.